LTC4263
19
4263fe
APPLICATIONS INFORMATION
Fuse
While the LTC4263 does not require a fuse for proper
operation or for compliance with IEEE 802.3af, some
safety requirements state that the output current must be
limited to less than 2A in less than 60 seconds if any one
component fails or is shorted. Since the LTC4263 is the
primary current limiter, its failure could result in excess
current to the port. To meet these safety requirements, a
fuse can be placed in the positive leg of the port. The fuse
must be large enough that it will pass at least 450mA when
derated for high temperature but small enough that it will
fuse at less than 2A at cold temperature. This requirement
can usually be satis ed with a 1A fuse or PTC. Placing the
fuse between the RJ-45 connector and the LTC4263 and
its associated circuitry provides additional protection for
this circuitry. Consult a safety requirements expert for the
application speci c requirements.
Power Supply
Poor regulation on the 48V supply can lead to
noncompliance. The IEEE speci cation requires a PSE
output voltage between 44V and 57V. When the LTC4263
begins powering an Ethernet port, it controls the current
through the port to minimize disturbances on V
SS
. However,
if the V
SS
supply is underdamped or otherwise unstable,
its voltage could go outside of the IEEE-speci ed limits,
causing the PSE to be noncompliant. This scenario can be
even worse when a PD is unplugged because the current
can drop immediately to zero. In both cases the port voltage
must always stay between 44V and 57V. Beyond this, the
IEEE 802.3af speci cation places speci c ripple, noise and
load regulation requirements on the PSE. Disturbances
on V
SS
can also adversely affect detection, classi cation
and AC disconnect sensing. For these reasons, proper
bypassing and stability of the V
SS
supply is important.
Another problem that can affect the V
SS
supply is
insuf cient power, leading to the supply voltage dropping
out of the speci ed range. The 802.3af speci cation states
that if a PSE powers a PD it must be able to provide the
maximum power level requested by the PD based on
the PDs classi cation. The speci cation does allow a
PSE to choose not to power a port, typically because the
PD requires more power than the PSE has available to
deliver. If a PSE is built with a V
SS
supply not capable of
delivering full power to all ports, it is recommended to
use the LTC4263 power management feature to prevent
ports from being turned on when there is insuf cient
power. Because the speci cation also requires the PSE
to supply an inrush current of 400mA at up to a 5% duty
cycle, the V
SS
supply capability should be at least a few
percent higher than the maximum total power the PSE
needs to supply to the PDs.
Isolation
The IEEE 802.3af standard requires Ethernet ports to be
electrically isolated from all other conductors that are
user accessible. This includes the metal chassis, other
connectors, and the AC power line. Environment A isolation
is the most common and applies to wiring within a single
building serviced by a single AC power system. For this
type of application, the PSE isolation requirement can be
met with the use of a single, isolated 48V supply powering
several LTC4263 ports. Environment B, the stricter isolation
requirement, is for networks that cross an AC power
distribution boundary. In this case, electrical isolation
must be maintained between each port in the PSE. The
LTC4263 can be used to build a multi-port Environment B
PSE by powering each LTC4263 from a separate, isolated
48V supply. In all PSE applications, there should be no
user accessible connections to the LTC4263 other than
the RJ-45 port.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LTC4268IDKD-1#PBF
IC PD HIGH POWER W/CNTRL 32-DFN
LTC4274CUHF#PBF
IC CONTROLLER POE 38-QFN
LTC4280CUFD#PBF
IC CONTROLLER HOT SWAP QFN-24
LTC4300-1IMS8#TRPBF
IC HOTSWAP 2WIRE BUS BUFFR 8MSOP
LTC4300A-2IMS8#TRPBF
IC BUFFER BUS 2WR HOTSWAP 8-MSOP
LTC4301IDD
IC BUFFER BUS HOTSWAP 2WR 8DFN
LTC4301LIDD#TRPBF
IC BUFFER BUS HOTSWAP 2WR 8DFN
LTC4302IMS-1#TRPBF
IC BUFFER 2-WIRE BUS 10-MSOP
相关代理商/技术参数
LTC4263IS-PBF
制造商:LINER 制造商全称:Linear Technology 功能描述:Single IEEE 802.3af Compliant PSE Controller with Internal Switch
LTC4263IS-TRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:Single IEEE 802.3af Compliant PSE Controller with Internal Switch
LTC4264
制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous No-Opto Flyback Controller
LTC4264CDE
制造商:LINER 制造商全称:Linear Technology 功能描述:High Power PD Interface Controller with 750mA Current Limit
LTC4264CDE#PBF
功能描述:IC CNTRLR PD INTERFACE 12-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264CDE#TRPBF
功能描述:IC INTERFACE 802.3AT 12-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264IDE
制造商:LINER 制造商全称:Linear Technology 功能描述:High Power PD Interface Controller with 750mA Current Limit
LTC4264IDE#PBF
功能描述:IC CNTRLR PD INTERFACE 12-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND